Boot Release Problem

Ford Fusion Boot Release Problem 

The boot latch won't open via button or key fob. I can press the button and see the latch move slightly but not enough to open the lock.The boot will still open via the key as normal.
It looks like a new solenoid is needed which if it's the right part can be bough for around £20 on eBay.

First remove the boot trim and check for part numbers. 

Removed the three screws but the plastic is till firmly in place.
Haynes manual says there are some plastic clips once you remove the 3 screws.
.
Remove the 3 screws from the tailgate trim and then lever around the edge to release the spring clips and then the trim cover can be taken off so that you can see the release mechanism. The lock is operated by either of two Bowden cables - one from the keyhole and one from the release motor. Try using the remote button on the key to see if the release motor is making an effort to pull the Bowden cable. Mine was just not moving the Bowden cable enough to spring the lock and so I have ordered a new release motor.

 I could see that the release motor was not moving the Bowden cable enough to spring the lock, I ordered a new release motor from FordParts UK (www.fordpartsuk.com). I have just fitted the new motor - very easy just two bolts and the wiring connector, and it works perfectly.


Go to the website www.fordpartsuk.com and then go down the list of vehicles and click on Fusion and then where it says enter Keyword - type in tailgate release motor. I paid £49.35 plus £4.00 p&p plus £10.67 VAT making a total of £64.02. Not particularly cheap but good to have it working properly again.

Comments

Post a Comment

Popular posts from this blog

How To Test for a Blown Head Gasket

Image
Blown Head Gasket Testing Nissan Runs Hot and overheats while driving The average cost for a Head Gasket(s) Replacement is between $1314 and $1679. Labor costs are estimated between $1270 and $1603 while parts are priced between $44 and $76.Get a personalized estimate based on your location and specific car. Estimate does not include taxes and fees. But first test and confirm that headgasket is faulty. If your 1.8L Nissan Sentra has severely overheated and doesn't start or it starts and runs but overheats (and you've already confirmed that the fan, thermostat and water pump work)... there's a good chance you've got a blown head gasket on your hands . There are 4 very simple tests that you can perform on your Nissan Sentra that will let you know if the head gasket has blown. In this tutorial, I'll show you how to perform them in a step-by-step way. To prevent an expensive, recurring problem, the integrity of the entire Nissan cooling system should be inspe...
Read more

How To Replace Electric Door Locks In Car?

Image
Door Lock Replacement The  electric door locks  inside of your car doors consist of a control switch, the locking door latch and/or an electric control solenoid. When the control switch is energized an electrical impulse forces the control solenoid to push or pull the locking mechanism depending on the command selected. (Lock and unlock). Anytime you have problems with an electric door lock check the  fuses  or thermo fuse the powers the system. Step 1 - Identity Door Switches and Controls Door Panel Components The average vehicle door has basic controls for the different functions the door performs. Interior light and safety reflector helps illuminate the interior of the vehicle. When the door is open the light and the reflector alert people from a distance your door is open. The electric window switch controls the electrical power to the window motor. The motor turns a series of gears and/or cables to power the window up and down. The electric door swit...
Read more

New Clutch Slips After Installation

Image
Adjustable Clutch Master Cylinders Clutch Slips If the clutch is cable operated then you might need to slacken the cable. Clutches are the opposite of brakes, as they wear brakes get slacker but clutches tighten up. If there's insufficient slack in the cable then this will prevent the clutch from fully engaging.  If it was slipping because you rode it, the plates would be glazed. Good plates would means that they did the job wrong. A greasy flywheel maybe. The pedal is stiffer because they used stronger springs when they did the job. If it's mechanical linkage, they might have left it too tight. poor job of replacing clutch assembly ,if  only replaced the disc and not resurfaced the flywheel and replace the pressure plate. Once they get glazed form slipping a new disc doesn't help very much. Look at your old receipt for the work, it should list the parts: clutch disc pressure plate pilot bearing throw-out bearing pressure plate job-out...resurface flywheel ...
Read more