delphi delco electronics radio wiring diagram for hyundai santa



Basically the diagram  of the large harness corresponds to the pins like this. Starting in the upper right hand corner and working down the right side from A12 down to A1. 1=Left rear output-red
2=Left rear output-blue 
3=Right rear output-black 
4=Right rear output-yellow 
5=empty 
6=Left front input-black 
7=Left front input-yellow 
8=Left rear input-orange 
9=Left rear input-green 
10=Amp 'ON'-blue&orange 
11=empty 
12=Amp sensor-black&orange 
Back up to upper left hand corner on the large plug diagram and working down. 13=Right front tweeter output-red 
14=Right front tweeter output-blue 
15=Left front tweet output-red 
16=Left front tweeter output-blue 
17=empty 
18=Right front input-red 
19=Right front input-white 
20=Right rear input-blue 
21=Right rear input-red 
23=Right front sub (+) output-yellow 
24=Right front sub (-) output-black 
The small harness is the same in the diagram above with the upper right position being pin 1 going down to pin 4 then back up to the top for pin 5 down to pin 8. 1=Memory Power-Lrg White 
2=Amp Ground- Lrg Black 
3=Left front sub (+)output-yellow 
4=Left front sub (-) output-black 
5=Left front mid (+) output-white 
6=Left front mid (-) output-brown 
7=Right front mid (-)output-brown 
8=Right front mid (+) output-white.

 =======================
i have an 05 gls with the monsoon system. i wanted to upgrade my speakers and headunit (radio). i did alot of research on the wiring and came to the conclusion it would be easier to run new wires to the speakers, that way if i wanted to sell the santy down the road i could just take my new stuff out and put the old speakers and radio back in. i used infinity kappa component set in the front doors and kappa 2 ways in the rear. i also added a pioneer radio/cd player in the dash. the radio was an easy install with a dash kit, wiring harness and antenna adaptor. running new speaker wires to each rear speaker was not that bad just time consuming as you have to remove alot of trim pieces. the door speakers were another story all together. i mounted the 6 1/2 down where the stock speakers were. the tweeter that came with my set mounted in the stock factory location up on the door wing, i took the stock one out and cut the wing panel and installed the tweeter there. i mounted the crossovers under the dash on a flat piece of black plastic under the steering wheel. the door factory wiring is run thru what they call a molex. its basically just a bigger male/female plug in so if you needed to replace the whole door you just unbolt it and unplug the molex and off comes the door. i found some openings in the molex that didn't have wires in them and drilled them out and ran my wires thru that and then thru the rubber wire covering so when i was done i just plugged the molex back together.

Comments

Post a Comment

Popular posts from this blog

How To Test for a Blown Head Gasket

Image
Blown Head Gasket Testing Nissan Runs Hot and overheats while driving The average cost for a Head Gasket(s) Replacement is between $1314 and $1679. Labor costs are estimated between $1270 and $1603 while parts are priced between $44 and $76.Get a personalized estimate based on your location and specific car. Estimate does not include taxes and fees. But first test and confirm that headgasket is faulty. If your 1.8L Nissan Sentra has severely overheated and doesn't start or it starts and runs but overheats (and you've already confirmed that the fan, thermostat and water pump work)... there's a good chance you've got a blown head gasket on your hands . There are 4 very simple tests that you can perform on your Nissan Sentra that will let you know if the head gasket has blown. In this tutorial, I'll show you how to perform them in a step-by-step way. To prevent an expensive, recurring problem, the integrity of the entire Nissan cooling system should be inspe...
Read more

How To Replace Electric Door Locks In Car?

Image
Door Lock Replacement The  electric door locks  inside of your car doors consist of a control switch, the locking door latch and/or an electric control solenoid. When the control switch is energized an electrical impulse forces the control solenoid to push or pull the locking mechanism depending on the command selected. (Lock and unlock). Anytime you have problems with an electric door lock check the  fuses  or thermo fuse the powers the system. Step 1 - Identity Door Switches and Controls Door Panel Components The average vehicle door has basic controls for the different functions the door performs. Interior light and safety reflector helps illuminate the interior of the vehicle. When the door is open the light and the reflector alert people from a distance your door is open. The electric window switch controls the electrical power to the window motor. The motor turns a series of gears and/or cables to power the window up and down. The electric door swit...
Read more

New Clutch Slips After Installation

Image
Adjustable Clutch Master Cylinders Clutch Slips If the clutch is cable operated then you might need to slacken the cable. Clutches are the opposite of brakes, as they wear brakes get slacker but clutches tighten up. If there's insufficient slack in the cable then this will prevent the clutch from fully engaging.  If it was slipping because you rode it, the plates would be glazed. Good plates would means that they did the job wrong. A greasy flywheel maybe. The pedal is stiffer because they used stronger springs when they did the job. If it's mechanical linkage, they might have left it too tight. poor job of replacing clutch assembly ,if  only replaced the disc and not resurfaced the flywheel and replace the pressure plate. Once they get glazed form slipping a new disc doesn't help very much. Look at your old receipt for the work, it should list the parts: clutch disc pressure plate pilot bearing throw-out bearing pressure plate job-out...resurface flywheel ...
Read more