How to Restore Foggy Headlight Lenses With Toothpaste

How to Restore Foggy Headlight Lenses With Toothpaste


Dust and oxidation build-up from driving can leave your headlight lenses looking foggy. Foggy headlights can impair your driving by dimming lighting and cutting down the range of your headlights. There are a number of expensive ways to clean the film and fog from your headlight lenses, but you can also clean your headlights at home using toothpaste.
How to Restore Foggy Headlight Lenses With Toothpaste
(Laura Vryhof/Demand Media)

Things You'll Need

  • Toothpaste
  • Scouring pad
  • Handheld buffer
  • Bucket of warm water
  • Lint-free cotton cloth
  • Paste car wax


Squeeze toothpaste generously onto the headlight. Use between 1/4 and 1/2 of the tube on one headlight.
Laura Vryhof/Demand Media
Smear the toothpaste around on the headlight with a scouring pad, covering the entire surface of the light.
Laura Vryhof/Demand Media
Buff the headlight thoroughly with a handheld buffing tool. You can also buff by hand, using the scouring pad; however, a buffing tool will get the job done more quickly.
Laura Vryhof/Demand Media
Rinse the headlight clean by pouring warm water over it and then drying with a lint-free cotton cloth. Repeat the process on the opposite side.
Laura Vryhof/Demand Media
Wax the headlights with a paste car wax and buff them again to keep dust and residue from building up on your headlights between cleanings.
Laura Vryhof/Demand Media

Comments

Post a Comment

Popular posts from this blog

How To Test for a Blown Head Gasket

Image
Blown Head Gasket Testing Nissan Runs Hot and overheats while driving The average cost for a Head Gasket(s) Replacement is between $1314 and $1679. Labor costs are estimated between $1270 and $1603 while parts are priced between $44 and $76.Get a personalized estimate based on your location and specific car. Estimate does not include taxes and fees. But first test and confirm that headgasket is faulty. If your 1.8L Nissan Sentra has severely overheated and doesn't start or it starts and runs but overheats (and you've already confirmed that the fan, thermostat and water pump work)... there's a good chance you've got a blown head gasket on your hands . There are 4 very simple tests that you can perform on your Nissan Sentra that will let you know if the head gasket has blown. In this tutorial, I'll show you how to perform them in a step-by-step way. To prevent an expensive, recurring problem, the integrity of the entire Nissan cooling system should be inspe...
Read more

How To Replace Electric Door Locks In Car?

Image
Door Lock Replacement The  electric door locks  inside of your car doors consist of a control switch, the locking door latch and/or an electric control solenoid. When the control switch is energized an electrical impulse forces the control solenoid to push or pull the locking mechanism depending on the command selected. (Lock and unlock). Anytime you have problems with an electric door lock check the  fuses  or thermo fuse the powers the system. Step 1 - Identity Door Switches and Controls Door Panel Components The average vehicle door has basic controls for the different functions the door performs. Interior light and safety reflector helps illuminate the interior of the vehicle. When the door is open the light and the reflector alert people from a distance your door is open. The electric window switch controls the electrical power to the window motor. The motor turns a series of gears and/or cables to power the window up and down. The electric door swit...
Read more

New Clutch Slips After Installation

Image
Adjustable Clutch Master Cylinders Clutch Slips If the clutch is cable operated then you might need to slacken the cable. Clutches are the opposite of brakes, as they wear brakes get slacker but clutches tighten up. If there's insufficient slack in the cable then this will prevent the clutch from fully engaging.  If it was slipping because you rode it, the plates would be glazed. Good plates would means that they did the job wrong. A greasy flywheel maybe. The pedal is stiffer because they used stronger springs when they did the job. If it's mechanical linkage, they might have left it too tight. poor job of replacing clutch assembly ,if  only replaced the disc and not resurfaced the flywheel and replace the pressure plate. Once they get glazed form slipping a new disc doesn't help very much. Look at your old receipt for the work, it should list the parts: clutch disc pressure plate pilot bearing throw-out bearing pressure plate job-out...resurface flywheel ...
Read more