How to Replace a Brake Light Switch on a 2006 Hyundai Elantra

How to Replace a Brake Light Switch on a 2006 Hyundai Elantra




The 2006 Elantra was in the third generation of this model. Produced by South Korean car manufacturer Hyundai since 1990, the car has been around for a long time.The car was originally assembled only in Ulsan, Korea, but since has been assembled in several countries, including the U.S. While the body design has seen several changes, the powerplant remained largely the same. Originally equipped with a Mitsubishi 1.6-liter engine producing only 113 horsepower, the 2006 had a 2.0 liter engine. While the brake light switch is in a tight location, it is something you can do at home.

Things You'll Need
Metric wrench set
Small flat-head screwdriver
Phillips head screwdriver
Plastic trim tool
Feeler gauge

 Instructions
Locate and remove the Phillips screws on the trim panel below the steering column. Take the trim tool and pop the upper section of the panel out of the clips, while pulling on the bottom. Remove the trim panel.

 Lay on your back look up under the dash. Locate the brake light switch on the brake pedal bracket. Follow the pedal arm up until you see the switch.

 Remove the harness connector by pushing the center tab with the flat-head screwdriver, then pull the connector from the switch.

 Remove the locking nut from the brake light switch, and unscrew the switch. Screw the new switch into the brake pedal bracket and start the lock nut. Turn the switch until the plunger reaches the pedal arm, then back it off about 3/4 turn. Using the feeler gauge, adjust the switch until the threaded end is 0.04 inches from the pad. Tighten the lock nut. Plug in the connector and test the switch by watching the brake lights. If they don't go off, back the switch out a bit more.

 Install the lower trim panel by snapping the top into the clips, then install the Phillips screws on the bottom and tighten.



Comments

Post a Comment

Popular posts from this blog

How To Test for a Blown Head Gasket

Image
Blown Head Gasket Testing Nissan Runs Hot and overheats while driving The average cost for a Head Gasket(s) Replacement is between $1314 and $1679. Labor costs are estimated between $1270 and $1603 while parts are priced between $44 and $76.Get a personalized estimate based on your location and specific car. Estimate does not include taxes and fees. But first test and confirm that headgasket is faulty. If your 1.8L Nissan Sentra has severely overheated and doesn't start or it starts and runs but overheats (and you've already confirmed that the fan, thermostat and water pump work)... there's a good chance you've got a blown head gasket on your hands . There are 4 very simple tests that you can perform on your Nissan Sentra that will let you know if the head gasket has blown. In this tutorial, I'll show you how to perform them in a step-by-step way. To prevent an expensive, recurring problem, the integrity of the entire Nissan cooling system should be inspe...
Read more

How To Replace Electric Door Locks In Car?

Image
Door Lock Replacement The  electric door locks  inside of your car doors consist of a control switch, the locking door latch and/or an electric control solenoid. When the control switch is energized an electrical impulse forces the control solenoid to push or pull the locking mechanism depending on the command selected. (Lock and unlock). Anytime you have problems with an electric door lock check the  fuses  or thermo fuse the powers the system. Step 1 - Identity Door Switches and Controls Door Panel Components The average vehicle door has basic controls for the different functions the door performs. Interior light and safety reflector helps illuminate the interior of the vehicle. When the door is open the light and the reflector alert people from a distance your door is open. The electric window switch controls the electrical power to the window motor. The motor turns a series of gears and/or cables to power the window up and down. The electric door swit...
Read more

New Clutch Slips After Installation

Image
Adjustable Clutch Master Cylinders Clutch Slips If the clutch is cable operated then you might need to slacken the cable. Clutches are the opposite of brakes, as they wear brakes get slacker but clutches tighten up. If there's insufficient slack in the cable then this will prevent the clutch from fully engaging.  If it was slipping because you rode it, the plates would be glazed. Good plates would means that they did the job wrong. A greasy flywheel maybe. The pedal is stiffer because they used stronger springs when they did the job. If it's mechanical linkage, they might have left it too tight. poor job of replacing clutch assembly ,if  only replaced the disc and not resurfaced the flywheel and replace the pressure plate. Once they get glazed form slipping a new disc doesn't help very much. Look at your old receipt for the work, it should list the parts: clutch disc pressure plate pilot bearing throw-out bearing pressure plate job-out...resurface flywheel ...
Read more