How to Install a Brake Booster on a 2005 Ford Expedition

How to Install a Brake Booster on a 2005 Ford Expedition


It was in the early 1920s when the prestigious carmaker Pierce-Arrow Motor Car Company added a vacuum assist to its brake systems, making them the first cars with a brake booster. Your 2005 Ford Expedition has come a long way from those early days. If you've driven a car with manual brakes -- and not many people around today have -- you have an appreciation for the power brakes that come standard on nearly every car sold in the U.S.


Things You'll Need:

  • Memory-saver device
  • Ratchet
  • Socket set
  • Nut-driver set
  • Allen driver set
  • Mechanic's wire or bungee cord
  • Pliers
  • Foot-pound torque wrench
  • Inch-pound torque wrench


Removal
Open the hood and allow the engine to cool, if necessary. Install a memory-saver device according to the manufacturer's procedure.

Loosen the negative battery cable terminal clamp nut, using a ratchet and socket. Rotate the terminal slightly on the post to help break it loose, then remove the terminal from the negative battery post. Route the loose cable away from the battery to prevent accidental contact.

Locate the air cleaner housing and air cleaner outlet tube. Loosen the air cleaner outlet tube hose clamp, using a nut-driver. Disconnect the MAF sensor electrical connector, then lift the air cleaner housing up and out of the engine compartment.

Using a ratchet and Allen driver, remove the power steering fluid reservoir retainer screws, and carefully move the reservoir aside to gain clearance for the booster removal.

Locate the brake fluid level sensor on top of the brake master cylinder, and disconnect the electrical connector. Disconnect the brake pressure switch wire from the bottom of the master cylinder, if applicable.

Using a ratchet and socket, remove the master cylinder mounting nuts, then discard the nuts. Slide the master cylinder off the mounting studs, and move it aside to gain clearance for the brake booster, without kinking any of the lines. Support the master cylinder with a wire or bungee cord so there is no strain on the brake lines or fittings.

Remove the two mounting bolts from the cooling system degas bottle, then position it to gain clearance for the booster.

Squeeze the tabs on the vacuum hose clamp, using pliers, then remove the vacuum hose from the hose barb on the booster. Remove the pedal travel sensor and booster solenoid wires, if applicable.

Working inside the passenger compartment, remove the brake linkage cotter pin, then slide the washer, bushing, switch and the pushrod end off the brake pedal stud.

Peel down the carpeting around the booster pushrod to access the booster retainer nuts. Remove the four retainer nuts, using a ratchet and socket. Lift the booster out of the engine compartment.

Installation
Move the new booster into position while threading the four mounting studs, and the booster pushrod, through the holes in the firewall. Install the retainer nuts and torque them to 16 foot-pounds, using a foot-pound torque wrench and socket.

Install the booster pushrod, washer, bushing and switch on the brake pedal stud, then install the cotter pin. Move the carpeting back into position over the booster retainer nuts.

Install the booster vacuum hose and hose clamp, then tighten the clamp securely. Install the pedal travel sensor and booster solenoid wires, if applicable. Install the engine cooling system degas bottle. Install the retainer bolts and torque them to 80 inch-pounds.

Install the master cylinder on the mounting studs. Install and torque the new retainer nuts to 16 foot-pounds. Install the brake level switch wire, and the brake pressure switch wire, if applicable.

Install the power steering fluid reservoir and retainer screws. Torque the screws to 8 foot-pounds. Install the air cleaner assembly. Install the air cleaner outlet tube and tighten the clamp securely. Install the MAF sensor connector.

Install the negative battery cable terminal on the negative battery post. Torque the terminal clamp nut to 44 inch-pounds. Remove the memory-saver.




Comments

Post a Comment

Popular posts from this blog

How To Test for a Blown Head Gasket

Image
Blown Head Gasket Testing Nissan Runs Hot and overheats while driving The average cost for a Head Gasket(s) Replacement is between $1314 and $1679. Labor costs are estimated between $1270 and $1603 while parts are priced between $44 and $76.Get a personalized estimate based on your location and specific car. Estimate does not include taxes and fees. But first test and confirm that headgasket is faulty. If your 1.8L Nissan Sentra has severely overheated and doesn't start or it starts and runs but overheats (and you've already confirmed that the fan, thermostat and water pump work)... there's a good chance you've got a blown head gasket on your hands . There are 4 very simple tests that you can perform on your Nissan Sentra that will let you know if the head gasket has blown. In this tutorial, I'll show you how to perform them in a step-by-step way. To prevent an expensive, recurring problem, the integrity of the entire Nissan cooling system should be inspe...
Read more

How To Replace Electric Door Locks In Car?

Image
Door Lock Replacement The  electric door locks  inside of your car doors consist of a control switch, the locking door latch and/or an electric control solenoid. When the control switch is energized an electrical impulse forces the control solenoid to push or pull the locking mechanism depending on the command selected. (Lock and unlock). Anytime you have problems with an electric door lock check the  fuses  or thermo fuse the powers the system. Step 1 - Identity Door Switches and Controls Door Panel Components The average vehicle door has basic controls for the different functions the door performs. Interior light and safety reflector helps illuminate the interior of the vehicle. When the door is open the light and the reflector alert people from a distance your door is open. The electric window switch controls the electrical power to the window motor. The motor turns a series of gears and/or cables to power the window up and down. The electric door swit...
Read more

New Clutch Slips After Installation

Image
Adjustable Clutch Master Cylinders Clutch Slips If the clutch is cable operated then you might need to slacken the cable. Clutches are the opposite of brakes, as they wear brakes get slacker but clutches tighten up. If there's insufficient slack in the cable then this will prevent the clutch from fully engaging.  If it was slipping because you rode it, the plates would be glazed. Good plates would means that they did the job wrong. A greasy flywheel maybe. The pedal is stiffer because they used stronger springs when they did the job. If it's mechanical linkage, they might have left it too tight. poor job of replacing clutch assembly ,if  only replaced the disc and not resurfaced the flywheel and replace the pressure plate. Once they get glazed form slipping a new disc doesn't help very much. Look at your old receipt for the work, it should list the parts: clutch disc pressure plate pilot bearing throw-out bearing pressure plate job-out...resurface flywheel ...
Read more