How to Clean Carbon Buildup in an IAC Valve

How to Clean Carbon Buildup in an IAC Valve



The idle air control valve, commonly referred to as the IAC valve, is responsible for adjusting idle speed. The IAC valve works closely with other electrical components to control the air moving around the throttle plate. If your vehicle begins to stall or has poor idle quality, your IAC valve may have carbon buildup and needs to be cleaned. Cleaning your vehicle's IAC valve is a simple task and only takes a few steps.

Things You'll Need
Owner's manual
Flat head screwdriver
Socket wrench
Carburetor cleaner
Rag


Instructions
Allow your vehicle to cool for 20 minutes before beginning any work.

Refer to your owner's manual for the exact location of the IAC valve in your vehicle. The IAC valve us normally near the throttle body.

Unplug the wiring harness connector using a flat head screwdriver to pry the snaps off. Using a socket wrench, unscrew the bolts holding the IAC valve into the block.

Examine the IAC valve; the needle part of the valve is normally where the carbon buildup is. Use carburetor cleaner to spray the needle and wipe the needle clean using a rag. Repeat this until the carbon buildup is cleaned off the needle. Allow the IAC valve to dry completely before reinstalling it.

Insert the IAC valve back into the block and tighten the two bolts. Plug the wire connector back into place. Start the vehicle and allow it to warm up for five minutes before driving it.



Comments

Post a Comment

Popular posts from this blog

How To Test for a Blown Head Gasket

Image
Blown Head Gasket Testing Nissan Runs Hot and overheats while driving The average cost for a Head Gasket(s) Replacement is between $1314 and $1679. Labor costs are estimated between $1270 and $1603 while parts are priced between $44 and $76.Get a personalized estimate based on your location and specific car. Estimate does not include taxes and fees. But first test and confirm that headgasket is faulty. If your 1.8L Nissan Sentra has severely overheated and doesn't start or it starts and runs but overheats (and you've already confirmed that the fan, thermostat and water pump work)... there's a good chance you've got a blown head gasket on your hands . There are 4 very simple tests that you can perform on your Nissan Sentra that will let you know if the head gasket has blown. In this tutorial, I'll show you how to perform them in a step-by-step way. To prevent an expensive, recurring problem, the integrity of the entire Nissan cooling system should be inspe...
Read more

How To Replace Electric Door Locks In Car?

Image
Door Lock Replacement The  electric door locks  inside of your car doors consist of a control switch, the locking door latch and/or an electric control solenoid. When the control switch is energized an electrical impulse forces the control solenoid to push or pull the locking mechanism depending on the command selected. (Lock and unlock). Anytime you have problems with an electric door lock check the  fuses  or thermo fuse the powers the system. Step 1 - Identity Door Switches and Controls Door Panel Components The average vehicle door has basic controls for the different functions the door performs. Interior light and safety reflector helps illuminate the interior of the vehicle. When the door is open the light and the reflector alert people from a distance your door is open. The electric window switch controls the electrical power to the window motor. The motor turns a series of gears and/or cables to power the window up and down. The electric door swit...
Read more

New Clutch Slips After Installation

Image
Adjustable Clutch Master Cylinders Clutch Slips If the clutch is cable operated then you might need to slacken the cable. Clutches are the opposite of brakes, as they wear brakes get slacker but clutches tighten up. If there's insufficient slack in the cable then this will prevent the clutch from fully engaging.  If it was slipping because you rode it, the plates would be glazed. Good plates would means that they did the job wrong. A greasy flywheel maybe. The pedal is stiffer because they used stronger springs when they did the job. If it's mechanical linkage, they might have left it too tight. poor job of replacing clutch assembly ,if  only replaced the disc and not resurfaced the flywheel and replace the pressure plate. Once they get glazed form slipping a new disc doesn't help very much. Look at your old receipt for the work, it should list the parts: clutch disc pressure plate pilot bearing throw-out bearing pressure plate job-out...resurface flywheel ...
Read more