How to Adjust Ford Drum Brakes

How to Adjust Ford Drum Brakes



Many times restoring proper brake pedal height and parking brake function is just a matter of adjusting the rear drum brakes on your Ford vehicle. As the brake shoes wear, the distance between the shoe and the drum increases. This causes the brake pedal or parking brake lever/pedal to move farther before the shoes make contact with the drum. Adjustment of the Ford drum brake system is well within the average home mechanic's ability.

Things You'll Need
Floor jack
Jack stands
Wheel chocks
Lug wrench
Drum brake adjusting tool

Instructions
Place wheel chocks behind the front wheels to prevent vehicle movement when the rear wheels are off. Raise the rear of the vehicle with the floor jack, and place jack stand under the frame. Lower the vehicle onto the jack stands to support the weight of the vehicle. Never rely on the floor jack alone to support the vehicle. Remove the rear wheels and place them, along with the lug nuts, out of the work area. This prevents tripping hazards, and lug nut loss.

Remove the drum, and inspect the rear brake shoes and drum for damage. Locate the star wheel adjuster. This serrated wheel shaped piece is between the lower edges of both shoes. As the wheel is turned, it expands on contracts the shoes. Remove the rubber plug in the back of the backing plate behind the star wheel adjuster.

Install the drum onto the shoes. Turn the star wheel with the brake-adjusting tool, until the shoes contact the drum. The shoes should not be so tight that the drum cannot turn, but there should be a slight drag on the drum as it is turned.

Reinstall the wheels and lower the vehicle. Check parking brake function by applying the parking brake, and putting the vehicle in gear. The parking brakes should hold under slight torque load from the engine.




Comments

Post a Comment

Popular posts from this blog

How To Test for a Blown Head Gasket

Image
Blown Head Gasket Testing Nissan Runs Hot and overheats while driving The average cost for a Head Gasket(s) Replacement is between $1314 and $1679. Labor costs are estimated between $1270 and $1603 while parts are priced between $44 and $76.Get a personalized estimate based on your location and specific car. Estimate does not include taxes and fees. But first test and confirm that headgasket is faulty. If your 1.8L Nissan Sentra has severely overheated and doesn't start or it starts and runs but overheats (and you've already confirmed that the fan, thermostat and water pump work)... there's a good chance you've got a blown head gasket on your hands . There are 4 very simple tests that you can perform on your Nissan Sentra that will let you know if the head gasket has blown. In this tutorial, I'll show you how to perform them in a step-by-step way. To prevent an expensive, recurring problem, the integrity of the entire Nissan cooling system should be inspe...
Read more

How To Replace Electric Door Locks In Car?

Image
Door Lock Replacement The  electric door locks  inside of your car doors consist of a control switch, the locking door latch and/or an electric control solenoid. When the control switch is energized an electrical impulse forces the control solenoid to push or pull the locking mechanism depending on the command selected. (Lock and unlock). Anytime you have problems with an electric door lock check the  fuses  or thermo fuse the powers the system. Step 1 - Identity Door Switches and Controls Door Panel Components The average vehicle door has basic controls for the different functions the door performs. Interior light and safety reflector helps illuminate the interior of the vehicle. When the door is open the light and the reflector alert people from a distance your door is open. The electric window switch controls the electrical power to the window motor. The motor turns a series of gears and/or cables to power the window up and down. The electric door swit...
Read more

New Clutch Slips After Installation

Image
Adjustable Clutch Master Cylinders Clutch Slips If the clutch is cable operated then you might need to slacken the cable. Clutches are the opposite of brakes, as they wear brakes get slacker but clutches tighten up. If there's insufficient slack in the cable then this will prevent the clutch from fully engaging.  If it was slipping because you rode it, the plates would be glazed. Good plates would means that they did the job wrong. A greasy flywheel maybe. The pedal is stiffer because they used stronger springs when they did the job. If it's mechanical linkage, they might have left it too tight. poor job of replacing clutch assembly ,if  only replaced the disc and not resurfaced the flywheel and replace the pressure plate. Once they get glazed form slipping a new disc doesn't help very much. Look at your old receipt for the work, it should list the parts: clutch disc pressure plate pilot bearing throw-out bearing pressure plate job-out...resurface flywheel ...
Read more