How to Tell If a Wheel Bearing Is Bad on Your Car?

How to Tell If a Wheel Bearing Is Bad on Your Car?




There are two common types of automotive wheel bearings used. Wheel hub bearing assemblies are becoming more and more popular, even on wheels with no drive axle. Wheel hub bearing assemblies come assembled with the bearings inside and are nonserviceable. The other older style of bearings are separate components from the wheel hub. The inner bearing and racer have to manually be pressed into the rear of the brake rotor or brake drum assembly and the front bearing is free-floating. These should be serviced (repacked with grease) every time a brake job is performed.

Things You'll Need
Wheel chock
Jack
Jack stands



Instructions
Test drive the vehicle to determine which axle (front or rear) the bearing noise (if applicable) is coming from. Faulty bearings can emit growling, whining, grinding, squealing or squeaking noises that intensify with the revolution of the tires.

Park the vehicle on level ground so you can safely lift the vehicle. Apply the parking brake if lifting the front of the vehicle. Do not apply the parking brake if lifting the rear axle or the parking brake will prohibit moving the wheels.

Place a wheel chock against the outside tread of the opposite axle from the one being lifted.

Hoist the respective axle up (one side at a time) with the jack and support each side with a jack stand placed in a safe position under the vehicle.

Place one hand on top of the tire and another hand at the bottom of the tire and try to wiggle the tire by pulling out on the top and pushing in on the bottom and then the other way around. Free-floating bearings (such as the front bearings on rear-wheel drive vehicles) allow a slight bit of play. However, hub bearing assemblies do not allow any play. If there is slight play, check to see if there is a drive shaft going through the wheel assembly. If there is not, there's a good chance it's a floating bearing style, but refer to the vehicle owner's manual to confirm. If there is a drive shaft going to the wheel, the hub bearing assembly is bad and needs to be replaced. Check both wheels of the axle in this fashion.

Rotate the tire if there is no play to determine if there is a noise (more on one side than the other) or slight resistance can be felt while the tire is rotating. Some vehicles may require having the transmission placed in the neutral position for this test. If there is any resistance or noise heard, the bearings should be inspected professionally and serviced or replaced. Floating bearings sometimes can be serviced and tightened, but hub bearing assemblies will require replacement.



Comments

Post a Comment

Popular posts from this blog

How To Test for a Blown Head Gasket

Image
Blown Head Gasket Testing Nissan Runs Hot and overheats while driving The average cost for a Head Gasket(s) Replacement is between $1314 and $1679. Labor costs are estimated between $1270 and $1603 while parts are priced between $44 and $76.Get a personalized estimate based on your location and specific car. Estimate does not include taxes and fees. But first test and confirm that headgasket is faulty. If your 1.8L Nissan Sentra has severely overheated and doesn't start or it starts and runs but overheats (and you've already confirmed that the fan, thermostat and water pump work)... there's a good chance you've got a blown head gasket on your hands . There are 4 very simple tests that you can perform on your Nissan Sentra that will let you know if the head gasket has blown. In this tutorial, I'll show you how to perform them in a step-by-step way. To prevent an expensive, recurring problem, the integrity of the entire Nissan cooling system should be inspe...
Read more

How To Replace Electric Door Locks In Car?

Image
Door Lock Replacement The  electric door locks  inside of your car doors consist of a control switch, the locking door latch and/or an electric control solenoid. When the control switch is energized an electrical impulse forces the control solenoid to push or pull the locking mechanism depending on the command selected. (Lock and unlock). Anytime you have problems with an electric door lock check the  fuses  or thermo fuse the powers the system. Step 1 - Identity Door Switches and Controls Door Panel Components The average vehicle door has basic controls for the different functions the door performs. Interior light and safety reflector helps illuminate the interior of the vehicle. When the door is open the light and the reflector alert people from a distance your door is open. The electric window switch controls the electrical power to the window motor. The motor turns a series of gears and/or cables to power the window up and down. The electric door swit...
Read more

New Clutch Slips After Installation

Image
Adjustable Clutch Master Cylinders Clutch Slips If the clutch is cable operated then you might need to slacken the cable. Clutches are the opposite of brakes, as they wear brakes get slacker but clutches tighten up. If there's insufficient slack in the cable then this will prevent the clutch from fully engaging.  If it was slipping because you rode it, the plates would be glazed. Good plates would means that they did the job wrong. A greasy flywheel maybe. The pedal is stiffer because they used stronger springs when they did the job. If it's mechanical linkage, they might have left it too tight. poor job of replacing clutch assembly ,if  only replaced the disc and not resurfaced the flywheel and replace the pressure plate. Once they get glazed form slipping a new disc doesn't help very much. Look at your old receipt for the work, it should list the parts: clutch disc pressure plate pilot bearing throw-out bearing pressure plate job-out...resurface flywheel ...
Read more