Serpentine Belt Replacement

How To Replace Serpentine Belt

Made of reinforced synthetic and/or hard rubber, belts are usually v-channeled or ribbed serpentine They're used to drive accessories including the alternator, water pump, AC compressor, power steering, air pump, vacuum pump and injector pump. They're usually driven by the engine's crankshaft pulley and are fully adjustable by tensioners or idlers that follow or track the surface of the belt.

PARTS
Tools and Supplies Needed
Socket set and ratchet
Serpentine Belt
Protective eyewear and gloves.
Flashlight
Accessory Belt Idler Pulley
Accessory Belt Tensioner
Screwdriver .

Before you begin place your car on a flat surface with the engine "off" in park with the parking brake on. Wear protective clothing, eyewear and gloves to avoid injury.


Safety Tip:
Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or closed toe shoes.


1
Open your hood and locate your vehicle's serpentine belt.
2
Locate the serpentine belt routing diagram in the engine compartment, in the vehicle owners manual, or under the hood.
3
Locate the serpentine belt tensioner.
6716Photo may not be specific to your vehicle
4
Move tensioner to loosen the belt.
5
Remove the serpentine belt.
6
Install the new serpentine belt making sure the belt is routed the same way as before.
6714Photo may not be specific to your vehicle
7
Check the belt tension. Push down in the middle of a section of the belt. It should not move more than a half inch.
8
Start the engine and allow the car to run for a few minutes to ensure proper belt installation.
9
Turn the engine off and recheck the serpentine belt tension. Adjust tension if needed. May require belt tensioner replacement.

Step 1 - Remove engine covers, shrouds or plastic guards that may cover the work area. (Needed to access to the front of the engine.)

Removing Air Filter Housing

Step 2 - Locate the belt tensioner which is under spring tension to hold pressure on the belt which keeps it secure.



Locating Belt Tensioner

Step 3 - Using a wrench push the tensioner in the opposite direction of the spring tension to release the tensioner.

Releasing Belt Tensioner

Step 4 - Once the tensioner is released move the belt off the nearest pulley.

Removing Serpentine Belt
Step 5 - Belt is now ready for removal

Belt Ready for Removal
Step 6 - Remove the belt from the bottom pulley and all idler pulleys and accessories.

Removing Serpentine Belt From Pulleys
Step 7 - Once the belt has been removed compare the old belt to the replacement belt. They should be a exact match in both length and width.


Belt Comparison
Step 8 - Once the new belt has been checked install the new serpentine belt onto the pulleys.


Installing New Serpentine Belt
Step 9 - Once the belt is on the engine pulleys activate the belt tensioner to complete the belt installation

Activate Tensioner Install Belt
Step 10 - Once the belt has been installed use a flashlight to inspect the belt location on the pulleys are aligned with the grooves of the belt.

Checking Belt Alignment
The is no adjustment is necessary to a serpentine belt, the tension is automatically maintained by spring tension.

MORE BELT REPLACE DETAILS AND DIAGRAMS:----
To replace a worn belt, locate the idler or generator pulley.
Loosen the hold-down fastener for the idler or generator pulley.
Pry the idler or generator pulley inward to release the belt tension and remove the belt.
Match the old belt up for size with the new replacement belt.
Observe the belt routing diagram in the engine compartment.
Install the new belt over each of the drive pulleys. Often the manufacturer recommends a sequence for feeding the belt around the pulleys.
Art courtesy of Delmar - Thomson Learning.
Pry out the idler or generator pulley to put tension on the belt.

MORE DETAILS ABOUT SERPENTINE BELT:---

A serpentine belt drives engine accessories such as the air conditioner compressor, power steering pump and alternator. Over time serpentine belts can crack and fail. If the serpentine belt breaks the operation of some accessories will stop. Steering will be difficult but not impossible to turn because the power assist will be non-operational and eventually the car battery will lose its charge. Belt routing can be confusing, make sure to take a picture or draw a routing diagram before removing the old belt.
Check the belt tension, if the belt is loose it can cause a chirping noise due to the lack of pressure needed for the belt to operate properly. Visit - Serpentine belt tensioner replacement.


Best Practices


Use a wire brush to clean the belt pulley grooves.
Always use the right size belt to maintain the proper amount of tension.
Do not use "belt dressing" or anti noise sprays. This is a temporary fix and will cause the replacement belt to fail prematurely because of contaminates on the pulley system.
With the belt removed, spin all the pulleys to make sure the bearings are good. When bearings fails they can squeal before they lock up and throw the belt off.


                                                                                                                                                                                                                                                                                                       

Comments

Post a Comment

Popular posts from this blog

How To Test for a Blown Head Gasket

Image
Blown Head Gasket Testing Nissan Runs Hot and overheats while driving The average cost for a Head Gasket(s) Replacement is between $1314 and $1679. Labor costs are estimated between $1270 and $1603 while parts are priced between $44 and $76.Get a personalized estimate based on your location and specific car. Estimate does not include taxes and fees. But first test and confirm that headgasket is faulty. If your 1.8L Nissan Sentra has severely overheated and doesn't start or it starts and runs but overheats (and you've already confirmed that the fan, thermostat and water pump work)... there's a good chance you've got a blown head gasket on your hands . There are 4 very simple tests that you can perform on your Nissan Sentra that will let you know if the head gasket has blown. In this tutorial, I'll show you how to perform them in a step-by-step way. To prevent an expensive, recurring problem, the integrity of the entire Nissan cooling system should be inspe...
Read more

How To Replace Electric Door Locks In Car?

Image
Door Lock Replacement The  electric door locks  inside of your car doors consist of a control switch, the locking door latch and/or an electric control solenoid. When the control switch is energized an electrical impulse forces the control solenoid to push or pull the locking mechanism depending on the command selected. (Lock and unlock). Anytime you have problems with an electric door lock check the  fuses  or thermo fuse the powers the system. Step 1 - Identity Door Switches and Controls Door Panel Components The average vehicle door has basic controls for the different functions the door performs. Interior light and safety reflector helps illuminate the interior of the vehicle. When the door is open the light and the reflector alert people from a distance your door is open. The electric window switch controls the electrical power to the window motor. The motor turns a series of gears and/or cables to power the window up and down. The electric door swit...
Read more

New Clutch Slips After Installation

Image
Adjustable Clutch Master Cylinders Clutch Slips If the clutch is cable operated then you might need to slacken the cable. Clutches are the opposite of brakes, as they wear brakes get slacker but clutches tighten up. If there's insufficient slack in the cable then this will prevent the clutch from fully engaging.  If it was slipping because you rode it, the plates would be glazed. Good plates would means that they did the job wrong. A greasy flywheel maybe. The pedal is stiffer because they used stronger springs when they did the job. If it's mechanical linkage, they might have left it too tight. poor job of replacing clutch assembly ,if  only replaced the disc and not resurfaced the flywheel and replace the pressure plate. Once they get glazed form slipping a new disc doesn't help very much. Look at your old receipt for the work, it should list the parts: clutch disc pressure plate pilot bearing throw-out bearing pressure plate job-out...resurface flywheel ...
Read more